How to Inspect Mobile Plant Before Every Shift

A mobile plant inspection is not a paperwork exercise to complete from the cab. It is the point where an operator can find a leaking hose, damaged tyre, faulty warning device or unsafe attachment before that issue affects people, production or property. Knowing how to inspect mobile plant properly helps operators meet site requirements, supports maintenance planning and makes every move a safe one.

Whether the plant is an excavator, loader, skid steer, telehandler, forklift, roller, grader, water cart or elevated work platform, the basic principle is the same: inspect it before use, operate it within its limits, and remove it from service when a safety-critical defect is found.

Start with the right inspection process

A pre-start inspection should follow the manufacturer’s instructions, the workplace’s plant risk controls and the site-specific checklist for that item of equipment. A generic checklist can be useful, but it must not replace checks that apply to a particular make, model, attachment or work environment.

Complete the inspection in a logical order. This reduces the chance of missing an item, particularly at the start of a busy shift or when working in poor weather, dust or low light. Many operators begin with a walk-around inspection, move to the cab and controls, then complete functional checks in a clear area.

Before touching the machine, confirm you are authorised and competent to operate it. Check the plant identification, the current service status and any tags, lock-out devices or notes from the previous shift. Never assume that a machine is ready simply because it is parked in the usual location or was operating yesterday.

How to inspect mobile plant from the outside

The walk-around is where many visible defects are found. Parked plant can still present hazards, so approach carefully. Watch for unstable ground, overhead hazards, other moving vehicles and stored energy in hydraulic systems.

Start at one point and work around the machine in the same direction each time. Look underneath before climbing on or starting the plant. Fresh oil, coolant, fuel or hydraulic fluid on the ground can indicate a leak that needs attention. A small leak may become a serious failure once the system is under pressure.

Check the general condition of the machine body, access steps, handrails, mirrors, windows and guards. Steps and handholds need to be secure and free of mud, grease and loose materials. Guards, covers and panels should be fitted correctly, not bent open, missing or held in place with temporary fixes.

Pay close attention to tyres, tracks and wheels. Look for cuts, exposed cords, excessive wear, loose wheel nuts, damaged rims, debris caught in tracks and signs of incorrect inflation where applicable. On tracked plant, inspect track tension, sprockets, rollers and track pads for obvious damage or excessive wear. Do not place hands or feet near components that could move unexpectedly.

Hydraulic hoses, fittings and cylinders deserve careful attention. Check for abrasion, cracking, blistering, leaks, damaged fittings and unsecured hoses. Never use your hand to search for a hydraulic leak. High-pressure fluid can penetrate the skin and requires urgent medical attention. Use an approved method under your workplace procedure and report suspected leaks.

Also inspect the work equipment and attachments. On an excavator, this includes the bucket, teeth, quick hitch and pins. On a forklift or telehandler, inspect forks, carriage, mast, chains and attachment locking devices. On a loader, check the bucket, cutting edge, pivot points and coupling arrangement. Confirm any attachment is compatible with the plant and secured as intended by the manufacturer.

Check the cab, safety systems and controls

Once the external inspection is complete, use three points of contact when entering the cab. Remove loose rubbish, drink containers and tools that could interfere with pedals or controls. Adjust the seat and mirrors before starting so you can reach all controls and maintain clear visibility.

Check the seatbelt for damage, correct operation and secure mounting. A functioning restraint is essential in plant fitted with rollover protective structures. Inspect the horn, lights, indicators, reversing alarm, beacon, windscreen wipers, washers, demisters and cameras or proximity systems where fitted. These systems support visibility and communication, but they do not remove the need for the operator to remain alert and use effective exclusion zones.

Review the instrument panel when the plant is started. Warning lights, gauges and displays can identify low oil pressure, high engine temperature, electrical faults, brake issues or other problems that may not be obvious during a walk-around. Allow the machine to warm up as required by the manufacturer and site procedure.

Test steering, service brakes, parking brake, travel controls and hydraulic functions in a safe, designated area. Keep people clear while checking movement, articulation, lifting functions or attachments. Listen for unusual noises and watch for delayed response, jerky operation, drifting implements or warning alarms.

For plant with lifting capability, make sure rated capacity information is legible and relevant to the configuration in use. Capacity can change with attachment type, load centre, boom extension, ground conditions and operating radius. If the load chart is missing, unreadable or does not match the attachment, stop and seek direction before lifting.

Inspect for the job, not just the machine

A plant inspection is incomplete if the operator only checks mechanical condition. The work area can change quickly, especially across construction, civil, mining, agriculture and transport sites. Before operating, assess the task and travel route.

Consider ground bearing capacity, soft edges, trenches, stockpiles, overhead powerlines, underground services, traffic routes, pedestrians, weather and visibility. Check whether the machine can safely access the area with its load, attachment or dimensions. A water cart, for example, may be mechanically sound but unsuitable for a soft shoulder or sloping haul road.

Confirm the plant has the right safety equipment for the task. This may include fire extinguishers, wheel chocks, first aid supplies, communication equipment, flashing lights, spill kits or dust suppression equipment, depending on site rules and the nature of the work. Check expiry dates and service tags where your workplace procedure requires it.

If operating near workers on foot, establish the separation controls before moving. Use designated exclusion zones, barriers, clear communication and spotters where required. A spotter must be positioned where they can see the work area and remain clear of the plant’s path. The operator must know the agreed signals and stop work if communication is lost.

Record defects clearly and act on them

A pre-start checklist is a record of the plant’s condition at a point in time. Complete it honestly and with enough detail for a supervisor or maintenance provider to understand the issue. Writing “faulty” or “needs repair” does not explain what is wrong, where it is located or how it affects safe operation.

Describe the defect, identify the plant, note the date and time, and record the action taken. For example, a useful entry might state that the left rear work light is inoperative, the machine was reported to the supervisor and it is not to be used for night work until repaired.

The correct response depends on the defect and the risk it creates. Minor housekeeping issues may be resolved before work begins. Other problems need to be reported and repaired promptly. Safety-critical defects, such as ineffective brakes, steering faults, damaged lifting components, hydraulic leaks, missing guarding or a failed seatbelt, require the plant to be isolated from use in line with workplace procedures.

Do not keep operating because production is behind schedule or because a repair is expected later in the day. Plant should only return to service once an authorised person confirms the defect has been addressed and the equipment is safe to use. Pre-start checks do not replace scheduled servicing, inspections or maintenance carried out by competent people.

Build consistency into every shift

The most effective mobile plant inspections are consistent rather than rushed. Use the same sequence, take the time needed for the conditions, and speak up when something does not look right. Operators who know their equipment are often the first to notice subtle changes, such as a new vibration, slower hydraulic response or an unusual smell.

Supervisors and employers also have a role in making inspections meaningful. They need practical checklists, clear reporting pathways, time to complete checks, defect follow-up and maintenance records that show problems are being managed. Training can strengthen operator confidence, but it should always be matched with site procedures and the specific equipment in use.

For Queensland worksites, a well-run inspection process supports safer plant operation across every shift. The goal is straightforward: identify problems early, make sound decisions and do not put people at risk to keep a machine moving.

Address

65 Bootooloo Road
Bowen, QLD

Phone

07 4785 2850

Follow Us