A chemical drum left beside a wash-down area, an unlabelled decanted container, or a rushed spray mix before the weather changes can turn routine farm work into a serious incident. To manage farm chemical hazards effectively, hazards need to be controlled before products are opened, mixed, transported or applied – not only when something goes wrong.
On Queensland farms, chemicals may be used for weed, pest and disease control, cleaning, fuel handling, animal health, maintenance and water treatment. The products and tasks vary, but the safety principle is consistent: know what is being used, understand the exposure risk and put practical controls in place that workers can follow every day.
Start with the chemical, the task and the people
A farm chemical risk assessment should look beyond the product label. Consider the whole job: who is handling the chemical, where the work happens, how it is mixed or applied, the equipment involved and what could go wrong during clean-up or storage.
For example, a herbicide application may involve concentrated product during mixing, exposure to spray drift during application, contaminated gloves and clothing afterwards, and residue on equipment. A worker may also be exposed while loading a spray unit, repairing a hose or washing down machinery. Each stage needs controls.
The Safety Data Sheet (SDS) and product label are essential starting points. They provide directions for safe handling, storage, first aid, spill response and personal protective equipment (PPE). Keep current SDSs accessible to workers, including staff who may work remotely or outside normal office hours. A chemical register helps supervisors and workers identify what is held on site and where it is stored.
It also pays to consider the people doing the work. New workers, contractors, seasonal staff and family members may not know the farm’s chemical procedures. Experience with machinery does not automatically mean someone understands the risks of a particular product or application method.
Control risks before relying on PPE
PPE matters, but it should not be the first or only control. Gloves, coveralls, boots, eye protection and respiratory protection can reduce exposure when they are selected, fitted, worn and maintained correctly. They cannot compensate for poor storage, leaking equipment or an unsafe mixing process.
Use the hierarchy of controls when planning the job. Where reasonably practicable, eliminate unnecessary chemical use or substitute a less hazardous product or method. For example, mechanical weed control may suit some areas, while a ready-to-use product may reduce the risk associated with mixing concentrates. These options are not always practical, particularly across broadacre operations, but they should be considered.
Engineering and administrative controls often make the biggest operational difference. A designated mixing area with good ventilation, suitable drainage and access to clean water can reduce exposure. Closed transfer systems, well-maintained spray equipment, clear exclusion zones and weather checks can help prevent incidents during application. Scheduling work to avoid high winds, extreme heat or nearby workers is a practical control, not an afterthought.
Select PPE for the product and task
PPE requirements should come from the label and SDS, then be matched to the actual task. Chemical-resistant gloves suitable for the substance are different from general work gloves. Eye protection must protect against splashes, while footwear and clothing need to reduce skin contact without creating heat stress concerns.
Respiratory protective equipment may be required for some products and work conditions. If tight-fitting respirators are used, workers need the right type and size of mask, compatible filters or cartridges, clean-shaven sealing surfaces and fit testing to confirm the facepiece can achieve an effective seal. Respirator fit testing supports a respiratory protection program, but it does not replace correct selection, training, inspection, cleaning and filter change procedures.
PPE should be stored away from chemicals and checked before use. Contaminated items need to be handled and cleaned according to manufacturer instructions. Damaged gloves, cracked goggles or worn respirator components should be removed from service promptly.
Make chemical storage orderly and secure
Chemical storage is one of the clearest indicators of a farm’s safety systems. A proper storage area reduces the chance of unauthorised access, incompatible products being stored together, leaks entering drains and workers grabbing the wrong container.
Store chemicals in their original, labelled containers wherever possible. Never use food or drink containers for chemicals. If a product must be decanted for a legitimate work purpose, the new container needs clear identification and must be suitable for the chemical. Unlabelled containers create avoidable risk, especially where multiple people access the shed.
The storage area should be secure, weather-protected and arranged so containers can be inspected. Keep products off the ground where appropriate, protect them from heat and direct sunlight, and separate incompatible chemicals as directed by their SDS. Maintain clear access for handling and emergency response. Fuel, fertiliser, pesticides, cleaning agents and veterinary products may have different storage requirements, so one general-purpose shed may not suit every product.
Check shelves, bunding, containers and signage routinely. Small leaks and corroded containers are easier to deal with early than after a product has spread across a shed floor or entered soil and water.
Build safe habits into mixing, spraying and clean-up
The highest exposure risk can occur when handling concentrates. Workers should read the label before each use, even when they have used the product previously. Formulations, directions and PPE requirements can change.
Use measured quantities, avoid splashing, and keep children, visitors, animals and non-essential workers out of the area. Ensure there is access to water for washing and an appropriate means of containing spills. Do not eat, drink or smoke while handling chemicals. Personal items such as mobiles should be kept clear of contaminated gloves and work surfaces.
Before spraying, inspect hoses, fittings, nozzles and tanks for wear or leaks. Confirm the application equipment is suitable for the product and task. Wind direction, wind speed, temperature and the location of neighbouring crops, houses, waterways and livestock all affect whether conditions are suitable to proceed. If conditions change, stop and reassess rather than pressing on to finish the job.
After application, follow the label directions for equipment cleaning, container rinsing and disposal. Wash hands and exposed skin thoroughly, remove contaminated clothing carefully, and keep chemical-contaminated wash water out of areas where it may create further risk. Empty containers and unused product require management in line with product directions and local requirements. Do not treat disposal as a simple rubbish task.
Prepare workers to respond to a spill or exposure
A practical emergency plan should cover likely incidents, not just major events. Workers need to know where to find SDSs, first aid supplies, spill response materials, emergency contacts and clean water. They should understand when to isolate an area, who to notify and when outside emergency assistance may be required.
Spill kits should be appropriate for the chemicals held on site and located where they can be reached quickly. A spill kit still needs trained people behind it. Workers should not attempt to clean up a spill if they do not understand the product hazards or do not have the required controls and PPE.
First aid information on the SDS and label should guide immediate actions following exposure. Keep chemical containers or product information available for responders where safe to do so. Record incidents and near misses, then review what allowed the event to occur. A leaking fitting, unclear instruction or missing glove size can reveal a system issue worth fixing across the farm.
Train, supervise and review the system
Written procedures are useful only when they reflect the way work is actually done. Walk through chemical tasks with workers and contractors. Ask them where exposure is most likely, what equipment causes delays and whether the required PPE is readily available. These conversations often identify controls that look adequate on paper but fail in the paddock or shed.
Training should cover site-specific chemical procedures, reading labels and SDSs, PPE use, storage, spill response and reporting. Supervisors should verify that workers can apply the procedure, particularly before they work unsupervised. Refresher training is valuable when new chemicals, equipment, workers or seasonal activities are introduced.
Regular reviews are also needed after an incident, a near miss, a change in product or a change to the work area. Corrsafe can support Queensland workplaces with practical WHS advice, respirator fit testing and safety training that helps teams strengthen their day-to-day controls.
Chemical safety on a farm is rarely about one perfect document or one piece of PPE. It comes from clear decisions made repeatedly: choosing the right product and method, keeping the shed orderly, checking equipment, preparing workers and stopping work when conditions are not right. That is how every move becomes a safer one.
